- CANON MX330 INSTALLATION DOWNLOAD 64 BIT
- CANON MX330 INSTALLATION DOWNLOAD DRIVERS
- CANON MX330 INSTALLATION DOWNLOAD DRIVER
- CANON MX330 INSTALLATION DOWNLOAD SOFTWARE
- CANON MX330 INSTALLATION DOWNLOAD PASSWORD
Product returned to a Canon USA repair facility or a Canon USA Authorized Service Facility ("ASF"), and proven to be defective upon inspection will be (a) repaired utilizing new, remanufactured, repaired and/or recycled parts (b) exchanged for new or (c) exchanged for a refurbished Product, as determined by the Canon USA repair facility or the ASF. The Product is warranted against defects in materials and workmanship under normal use and service (a) for a period of one (1) year from the date of original purchase when delivered to you in new condition in its original container or (b) for (1) year from the date of original purchase for refurbished Products. ("8220 Canon USA") with respect to the new or refurbished Canon-brand product ("Product") packaged with this limited warranty, when purchased and used in the United States only. The limited warranty set forth below is given by Canon U.S.A., Inc.
CANON MX330 INSTALLATION DOWNLOAD DRIVER
So it looks as though the MX330 working under the same driver should work.Limited Warranty & InstantExchange Program DetailsĬanon U.S.A., Inc. I think it may be something to do with the backends not copied from /usr/lib to /usr/lib64. 'Received 152 bytes of unknown back channel data!'īut it still prints. However on the third and subsequent pressing of the Test button it comes up briefly with this odd error message: Restarted the CUPS server by making two equal and opposite trivial changes in CUPS itself.ġ8) Realised the Start Printer button for 'canontest' was highlighted so clicked on that and printer fired into life and produced two excellent Test Printer pages.
![canon mx330 installation download canon mx330 installation download](https://1.bp.blogspot.com/-z1KqZPWGpZg/X5Lu2W69GoI/AAAAAAAABes/aOofjyIpwTs7rT2UWkBc-rKDeZ49cPviwCNcBGAsYHQ/s384/Canon%2BPIXMA%2BMX922%2BDriver.png)
There is some backend stuff in a similar situation but I left that for now.ġ7) Attempted to do a test page for 'canontest' but it still complained about the missing filter as before.
CANON MX330 INSTALLATION DOWNLOAD 64 BIT
I think there was an earlier post about this possible problem and the cause is that CUPS, on a 64 bit system, looks in '/usr/lib64' for some components instead of '/usr/lib' where the Canon rpms store them.ġ6) Decided to do a naughty and copied 'pstocanonij' from '/usr/lib/cups/filter' to '/usr/lib64/cups/filter'.
![canon mx330 installation download canon mx330 installation download](https://www.zeytech.de/media/image/product/13414/lg/canon-pixma-ts5050~2.jpg)
'Filter pstocanonij for printer canontest not available.
CANON MX330 INSTALLATION DOWNLOAD PASSWORD
Accepted the suggestion.ġ3) CUPS then asked for a user name and password and I entered 'root' and its password.ġ4) CUPS reported that 'Printer canontest has been successfully installed' (roughly - I didn't write that all down) and then showed the 'Set Printer Options' page.ġ5) Changed the paper size from US letter to A4 and clicked the 'Set Printer Options' button. On the Device drop down list on the next page I now had the relevant options of:ġ2) Clicked continue and after several seconds it then proceeded to the next page where the 'Canon MX330 series Ver 3.10' entry was highlighted in the drop down list of PPD files. 'Usblp' is a kernel module and its presence showed up under 'lsmod|grep usblp'ġ1) All seemed well on the hardware side so ran CUPS again and added a new printer called 'canontest'. Checked 'dmesg' which showed the printer had been assigned to port '/dev/usb/lp0' with driver 'usblp'. Exit CUPS.ġ0) Plugged Canon MX310 (this is usually connected to my openSUSE 11.0 system) into a USB port and powered on. Printer had still not been powered on or connected to the computer at this stage.ĩ) Went to 'Manage Printing' (CUPS at localhost:631) and checked to see if there were any USB options for Adding a new USB printer. Clicked to accept.Ĩ) Re-Logged on as root (very bad, I know, but it does save a lot of time in some situations). Note that the 64bit verion 'libpopt0' was already installed. This showed the 'cnijfilter-common' and 'libpopt0-32bit' rpms had been chain selected as dependencies.
![canon mx330 installation download canon mx330 installation download](https://c1.neweggimages.com/ProductImageCompressAll1280/28-102-358-03.jpg)
The two rpms are called 'cnijfilter-common' and 'cnijfilter-mx330series'Ħ) Selected the 'cnijfilter-mx330series' for installation and then checked the 'Installation Summary' tab.
CANON MX330 INSTALLATION DOWNLOAD SOFTWARE
You can set up such a personal repository for the odd package under Yast.Ĥ) Ran Yast and than Software Management.ĥ) Searched for the string 'cnij'. This is a gzipped tar that contains two rpms and an 'install.sh' script.Ģ) Extracted the two rpms and ignored the 'install.sh' scriptģ) I moved the two rpms to my local, simple directory, repository at '/usr/local/rpm'.
CANON MX330 INSTALLATION DOWNLOAD DRIVERS
I decided to try installing the Canon MX330 drivers myself (Canon do not provide a Linux driver for the MX310 note) as follows:ġ) Downloaded the RPM package from the Canon site. However, working on the assumptions that:Ī) the MX330 has more or less the same guts as the MX310 with just a newer plastic box andī) openSUSE 11.2 is a slightly enhanced version of openSUSE 11.1, I cannot replicate s660117's situation exactly because I have openSUSE 11.2 and a Canon MX310 and he/she has openSUSE 11.1 and a Canon MX330. Well here I am again hopefully with some positive news.